Skip to content
Powered by Pagefind
English
Cozy Game Restoration Guides

Toro the Cat 2 Stuck Near 100 Percent: What to Try

The Toro the Cat 2 cartridge stalls on its back label and grooves. Here is how the UV torch, autocomplete and a better tool find the dirt you cannot see.

11/5/2026 Last updated: 11/5/2026 4 min read
Tweezers lifting a sticker from a cartridge pulled from an opened parcel
The back label is where the Toro the Cat 2 clean usually stalls. Official game imagery © Parasol Corp. Image source

Why does Toro the Cat 2 stall near the end?

Two reasons stack. The shell is a Galaxis 16 cartridge, which has the deepest moulding in the game, and the back label sits over seams where dirt can render slightly inside the shell — visible as a smudge you cannot touch.

That second part is not your technique. Dirt is projected onto the model in real time and can occasionally clip through the geometry — uncommon, but extremely annoying when it happens.

What does the stuck pattern look like?

Everything else cleans normally, the back stalls at 98–99%, and the marks that remain sit on or around the rear label — sometimes along the seam where the two shell halves meet. On some copies the mark that will not clear is the sticker with the line pattern on the back.

If that matches what you are seeing, the cartridge is not soft-locked. The finish is being held by a layer below the threshold.

What should I try first?

Work through this in order — most cases resolve in the first three steps.

  1. Sweep with the UV torch from a low angle. The torch highlights grime and leaves a trail on dirt, so a slow pass across the back tells you whether the mark is on the surface or inside it.
  2. Use the toothbrush on the back label and seams. The swab rides over the seam; the bristles get into it. This is the single most common fix for a Galaxis 16 that will not finish.
  3. Move the sun. The daylight slider changes the light angle through the window, and a different angle stops the plastic shimmering in a way that reads as leftover ink. Several players use it as a diagnostic: if the mark disappears at another sun position, it was reflection.
  4. Clean the tool. A loaded swab on a nearly clean label smears a grey film that looks exactly like unfinished dirt.
  5. Rotate the cartridge and check the back at eye level rather than from above. The rear label curves away from a high camera.

If the UV torch shows nothing glowing and the bar is still short, skip to the next section — you are probably at the point where more scrubbing does nothing.

Does autocomplete help?

Yes, and this is the case it was built for. Autocomplete fires when every layer reaches 99% or higher and clears the remainder, which is precisely the situation where a few pixels of clipped dirt would otherwise hold a cartridge hostage.

It is on by default. If you have turned it off in Accessibility, this is the cartridge to turn it back on for — or accept the finish at 99% and move on, because the difference between 99% and 100% is a grade, not a lock.

Will better tools fix it?

Eventually, yes. Tool power comes from the shelf, and a stronger tool is much less likely to leave semi-transparent residue behind on a surface like this one. That means the long-term fix is a better shelf rather than a better technique: rarity and shelf bonuses explains how the bonuses stack.

In the short term, one stuck cartridge is not worth rebuilding the room for. Finish it as close as you can, shelve it, and come back to a fresh copy later — duplicates are normal, and a second Toro the Cat 2 may generate clean.

Is it a bug I should report?

If the mark glows under UV but no tool moves it, if it survives a tool change and a clean swab, and if it sits exactly on the seam, it is worth a post in the Steam discussions with the platform, the region and the rarity — that is the detail that makes a clipping report reproducible.

The general-order advice for a normal cartridge is on scratches and polish; if the problem is the tutorial rather than the cartridge, start with heat gun step not completing.

Related Articles

Was this helpful?